Shandong Baimaoxing Iron and Steel Co., Ltd.
Contact Us
Inquiry
Form loading...

GR1 vs GR2 Titanium Plates: Corrosion Resistance, Plasticity & Price

A Chemical Equipment Material-Selection Decision Guide: Cost–Corrosion Trade-Offs, Deep Formability Analysis, and the Three-Step Engineering Verification Method

Material Selection Blueprint

1. Executive Engineering Summary

Evaluating CP Grade 1 and Grade 2 titanium through the lens of process metallurgy, chemical corrosion boundaries, mechanical allowable stress, and procurement lifecycle economics.

≥ 40%
GR1 Max Elongation
≈ 99 MPa
GR2 Allowable Stress (RT)
15%–25%
Procurement Premium (GR1)
< 0.05 mm/a
Typical Passive Corrosion Rate

Document Baseline: Chemical-equipment material-selection decision guide for design and procurement engineers. Standards referenced include GB/T 3621—2022 (Ti & Ti-alloy plate), GB/T 14845—2020, GB 150.2, and ASME BPVC VIII Div.1. Price references represent typical commercial wholesale market bands (reference basis: October 2026 bulk-market index; actual current mill quotes govern design procurement). Note: allowable-stress values herein are approximate design references; formal code calculations must utilize certified baseline figures.

Inverse Strength & Ductility

Tensile ranking stands at GR5 > GR2 > GR1 (895–1100, 440–620, 370–530 MPa), while elongation ranks strictly GR1 > GR2 > GR5 (≈40%, 35%, 10%). GR1 delivers unparalleled deep-draw formability among industrial pure titanium grades.

Ductility Covers Strength

When operating pressure is mild, vessel diameter compact, and nominal wall thickness is dictated by corrosion allowance or minimum mechanical rigidity rather than internal pressure, GR1’s unmatched ductility eliminates scrap and simplifies complex cold flanging.

The GR2 / GR5 Mandatory Threshold

For high-pressure, large-diameter shells, or temperatures exceeding 150°C, allowable stress becomes the sole design limiter. GR2 yields a 13%–15% thinner shell wall. For dynamic agitator shafts or extreme cyclical loads, GR5 (Ti-6Al-4V) is mandatory.

Procurement Justification

GR1 commands a 15%–25% cost premium over GR2 due to tighter sponge sorting and lower oxygen thresholds. This expense is justifiable only if offset by zero stamping cracking, fewer intermediate annealing steps, and reduced joint weld embrittlement.

Metallurgical Data

2. Key Parameter Matrix: GR1 vs GR2 vs GR5

Comparative mechanical properties, design stress thresholds according to ASME Section VIII Div. 1, and reference raw material price spreads.

Property / Engineering Metric GR1 (UNS R50250 / TA1) GR2 (UNS R50400 / TA2) GR5 (UNS R56400 / TC4)
Microstructure & Alloy Type Unalloyed alpha (α) pure Ti Unalloyed alpha (α) pure Ti Alpha-beta (α+β) dual phase
Tensile Strength Rm (MPa) 370 – 530 440 – 620 895 – 1100
Yield Strength Rp0.2 (MPa) ≥ 250 ≥ 320 ≥ 825
Elongation at Break A (%)
(By gauge per GB/T 3621—2022)
≥ 40 / 30 / 25 % ≥ 35 / 30 / 25 / 18 % ≥ 10 / 9 %
Allowable Design Stress [σ] (MPa)
(RT to 100°F, ASME BPVC VIII-1)
≈ 86 MPa ≈ 99 MPa (+15.1%) ≈ 193 MPa (+124%)
Interstitial Limits (Max wt%) O: 0.18 | Fe: 0.20 | C: 0.08 | N: 0.03 O: 0.25 | Fe: 0.30 | C: 0.08 | N: 0.03 O: 0.20 | Fe: 0.40 | V: 3.5-4.5 | Al: 5.5-6.75
Density (g/cm³) 4.51 4.51 4.43
Market Price Range (¥10,000 / Metric Ton) 7.0 – 13.5 6.6 – 12.5 14.0 – 26.0
Cost Differential Basis ≈ 15%–25% Premium over GR2 Baseline benchmark 2.0× – 2.5× Baseline

Note: Thickness partitions for elongation per GB/T 3621—2022: GR1 (0.3–2.0 / 2.0–10.0 / 10.0–30.0 mm); GR2 (0.3–1.0 / 1.0–2.0 / 2.0–10.0 / 10.0–30.0 mm); GR5 (5.0–10.0 / 10.0–100.0 mm).

Room-temperature mechanical properties of GR1, GR2, and GR5 titanium plates per GB/T 3621-2022
Fig. 1 Room-temperature mechanical properties comparison (GB/T 3621—2022, annealed plate, thin-gauge band).
Allowable design stress vs metal temperature curve for GR1 and GR2 per ASME Section VIII Div 1
Fig. 2 Allowable stress vs. metal temperature profile (ASME BPVC VIII Div.1 basis, approximate reference).
Procurement price spread and cost band for GR1, GR2, and GR5 titanium plates
Fig. 3 Raw material price-range comparison of GR1 / GR2 / GR5 industrial titanium plates (reference bulk market).
Corrosion Engineering

3. Corrosion Resistance: Commonalities & Boundary Realities

Analyzing passive rutile/anatase TiO₂ protective films, oxygen/iron interstitial partitioning, and crevice corrosion susceptibility limits.

Broad Process Neutrality (Shared Chemistry)

Both GR1 and GR2 are classified as commercially pure (CP) unalloyed titanium with an identical single-phase alpha grain matrix. In oxidizing environments, their behavior is virtually indistinguishable:

  • Wet Chlorine Gas & Hypochlorites: Forms instantaneous stable oxide films; corrosion rates remain below 0.01 mm/year up to 90°C.
  • Nitric Acid (HNO₃): Resistant across concentrations up to boiling point (caution required with red fuming nitric acid to prevent pyrophoric reactions).
  • Marine & Hypersaline Media: Flawless immunity to ambient seawater, brackish currents, and brine up to 75°C without pitting risk.
  • Organic Carboxylic Acids: High resistance to hot acetic acid, terephthalic acid, and formic streams where stainless steels rapidly stress-crack.

Subtle Interstitial Metallurgical Edge (GR1)

GR1 maintains strictly curtailed oxygen (≤0.18%) and iron (≤0.20%) ceilings compared to GR2 (O ≤0.25%, Fe ≤0.30%). This marginal reduction gives GR1 distinct performance nuances in specific edge-case scenarios:

  • Lower Interstitial Segregation: Reduced Fe content prevents micro-galvanic Fe-Ti intermetallic precipitation along grain boundaries, lowering local active dissolution sites.
  • Passive Film Homogeneity: The spontaneously regenerated TiO₂ passive layer on GR1 shows fewer defect vacancies in moderately reducing acidic transitions.
  • Hydrogen Embrittlement Resistance: Slower hydride pickup in cathodic polarization conditions, providing an extra safety cushion against hydrogen cracking.
  • The Specialty Boundary: Note that GR1 cannot replace palladium-stabilized alloys (Gr.7/Gr.11) or nickel-moly grades (Gr.12) in hot uninhibited HCl or H₂SO₄.
Decision Matrix

4. Strategic Selection: When Does Plasticity Trump Strength?

Evaluating internal pressure vs. corrosion allowance dominion to prevent buying surplus yield strength that compromises fabrication yields.

Equipment / Duty Characteristic Controlling Design Mechanism Optimal Grade Engineering Justification
Low-Pressure, Thin Chemical Scrubbers Corrosion Allowance & Rigidity GR1 Calculated pressure thickness is <1.0 mm. Actual wall (3.0 mm) is governed by minimum plate stiffness. GR2 strength is entirely wasted.
Plate-and-Frame Heat Exchanger Plates Deep Hydraulic Stamping (Chevron) GR1 Requires ≥40% elongation. GR1 prevents edge micro-tearing and work-hardening during complex pattern embossing at 0.5–0.6 mm gauges.
Expanded Tube-to-Tubesheet Heat Exchangers Radial Plastic Flow / Roll Expansion GR1 Low springback and high ductility ensure leak-free seal expansion into serrated tube holes without stress-cracking tube ends.
High-Pressure Reaction Autoclaves Membrane Tensile Stress ([σ]) GR2 15% higher allowable stress directly translates into a 13%–15% shell thickness reduction, significantly lowering equipment weight and cost.
Elevated Temperature Columns (>150°C) Thermal Yield Derating GR2 GR1 allowable stress deteriorates rapidly beyond 150°C. GR2 maintains reliable structural safety margins under elevated pressure codes.
Mixer Shafts, Impellers & Flanges Torsional Fatigue & Bolt Preload GR5 (TC4) CP grades exhibit insufficient yield and shear limits. GR5 provides 825 MPa yield strength, resisting continuous bending and shaft deflection.

The Metallurgical Rule of Thumb:

When calculated membrane stress thickness $t_{\text{pressure}} \le C_{\text{corrosion}} + t_{\text{forming}}$, the vessel is strictly corrosion/geometry-driven. The higher yield point of GR2 provides zero reduction in metal consumption. In this regime, GR1’s 40% elongation prevents premature cracking during deep dishing, spin flanging, and tight-radius coil bending, easily offsetting its nominal price premium through reduced rework and scrap rates.

Systematic Engineering Process

5. The Three-Step Selection-Verification Method

A quantitative framework to verify whether paying a 15%–25% premium for GR1 delivers a measurable economic and operational return.

Flowchart showing the three-step material selection verification method from corrosion rate to cost calculation
Fig. 4 Three-step material-selection verification flow (Corrosion Rate → Wall Allowance → Lifecycle Cost Accounting).
1

Step 1: Corrosion Rate ($v$) to Corrosion Allowance ($C$) Determination

Quantify actual wall degradation based on process fluid exposure across the intended operational design life. The baseline corrosion allowance is calculated as:

$$C = v \times L_{\text{design}} + C_{\text{fabrication}}$$

Where $v$ is media corrosion rate (mm/a), $L_{\text{design}}$ is operational lifespan in years, and $C_{\text{fabrication}}$ is minimum metal loss during surface pickling, polishing, or forming thinnings. If $C$ dominates the cross-section, structural strength criteria are secondary, making GR1 an immediate front-runner.

2

Step 2: Pressure-Driven Minimum Shell Wall Verification

Calculate minimum pressure-retaining wall thickness using standard pressure vessel codes (e.g., ASME Section VIII Div. 1, UG-27 or GB 150.3):

$$t = \frac{P \cdot D_i}{2[\sigma]\phi - P} + C$$

Here, $P$ is design internal pressure (MPa), $D_i$ is vessel internal diameter (mm), $[\sigma]$ is maximum allowable stress at design temperature (MPa), and $\phi$ is weld joint efficiency factor. By comparing the calculated thickness for GR1 ($[\sigma] \approx 86\text{ MPa}$) against GR2 ($[\sigma] \approx 99\text{ MPa}$), engineers establish whether the higher yield strength of GR2 allows stepping down to a thinner standard nominal plate size.

3

Step 3: Total Lifecycle Cost Accounting & Premium Recovery Decision

Evaluate total fabrication economics rather than raw sheet cost alone. Apply the financial recovery balance equation:

$$\Delta \text{Net} = (W_{\text{GR2}} \cdot K_{\text{GR2}} + F_{\text{GR2}}) - (W_{\text{GR1}} \cdot K_{\text{GR1}} - S_{\text{forming}} - R_{\text{weld}})$$

Where $W$ is total weight (kg), $K$ is unit purchase cost ($/kg), $F$ is labor cost, $S_{\text{forming}}$ represents cold-forming scrap reduction savings, and $R_{\text{weld}}$ accounts for reduced post-weld joint repair and NDT fail rates. If $\Delta \text{Net} > 0$, GR1 is mathematically justified despite the upfront price premium.

// WORKED ENGINEERING CASE STUDY: PRESSURE VESSEL COLUMN

Demonstrating when high allowable stress overrides ductility advantages:

Design Parameters: Design Pressure (P) = 1.6 MPa | Internal Diameter (Di) = 1200 mm
Weld Joint Efficiency (φ) = 0.85 | Design Life = 20 Years | Corrosion Rate (v) = 0.05 mm/a
Total Allowance (C = 0.05 × 20 + 1.0 mm forming allowance) = 2.0 mm
Material Density (ρ) = 4510 kg/m³
--------------------------------------------------------------------------------
[Calculation Step 1 - Membrane Thickness]:
• GR1: t_press = (1.6 × 1200) / (2 × 86 × 0.85 - 1.6) = 1920 / 144.6 ≈ 13.2 mm
• GR2: t_press = (1.6 × 1200) / (2 × 99 × 0.85 - 1.6) = 1920 / 166.7 ≈ 11.5 mm

[Calculation Step 2 - Total Nominal Plate Specification]:
• GR1 Total: 13.2 + 2.0 = 15.2 mm (Requires nominal 16 mm plate)
• GR2 Total: 11.5 + 2.0 = 13.5 mm (Requires nominal 14 mm plate)

[Calculation Step 3 - Weight and Cost Impact per Linear Meter]:
• GR1 Shell Mass: π × (1.200 + 0.016) × 0.016 × 4510 ≈ 275.6 kg/m
• GR2 Shell Mass: π × (1.200 + 0.014) × 0.014 × 4510 ≈ 241.0 kg/m
• Shell Material Weight Savings using GR2: 34.6 kg/m (12.5% reduction)

[Financial Assessment]:
Assuming GR2 baseline raw material price = ¥80/kg ($11.5/kg)
Assuming GR1 carries a 20% premium = ¥96/kg ($13.8/kg)
• Shell Material Cost (GR2) = 241.0 kg × ¥80 = ¥19,280 / meter
• Shell Material Cost (GR1) = 275.6 kg × ¥96 = ¥26,457 / meter
--------------------------------------------------------------------------------
ENGINEERING VERDICT: GR2 provides a net savings of ¥7,177 per meter (≈ 27% total savings). Because this shell is strictly strength-driven, choosing GR1 would add unnecessary expense without operational benefit.

COUNTER CASE: At P = 0.4 MPa and Di = 500 mm, both grades yield a calculated pressure thickness under 1.2 mm. Minimum nominal plate thickness is dictated entirely by 3.0 mm fabrication stability. In this regime, GR1 carries no weight penalty, and its high elongation makes cold dishing and flanging seamless.
Final Recommendations

6. Procurement Execution: Getting Full Value for the Premium

Practical sourcing advice for plant asset managers, equipment design teams, and procurement specialists.

1. Classify the Design Driver First

Never approve material requisitions on grade nomenclature alone. Establish whether the vessel is strength-governed or corrosion/geometry-governed. If calculated pressure thickness is negligible, standardizing on GR1 eliminates forming defects and downstream quality claims.

2. Specify Oxygen Ceilings Clearly

When purchasing GR1 for critical deep-stamping (such as PHE plates), specify certified low-interstitial sponge. Ensure mill test certificates explicitly guarantee O ≤ 0.15% and Fe ≤ 0.15% to take full advantage of its deep-drawing envelope.

3. Rely on GR2 as the Plant Workhorse

GR2 remains the balanced baseline for chemical processing. For standard welded columns, storage tanks, and non-drawn pipe systems under 150°C, GR2 offers the most economical mix of weldability, structural strength, and raw material availability.

4. Audit Delivered Thickness Bands

For pressure shells, compare standard plate gauge availability from your rolling mill. If moving from GR1 to GR2 does not allow you to step down a standard nominal plate thickness (e.g., from 12 mm to 10 mm), the structural advantage of GR2 may not translate into real-world weight savings.

Technical Governance

7. Appendix: Standards, Source References & Design Notes

International codes, standard specifications, and engineering compliance databases supporting this guide.

Governing Specification Standard Designation Scope & Technical Application
Titanium and Titanium-Alloy Plate, Sheet & Strip GB/T 3621—2022 Table 5 mechanical property baselines at ambient temperature for TA1, TA2, and TC4 (corresponding to ASTM GR1, GR2, GR5).
Titanium Plate for Plate Heat Exchangers GB/T 14845—2020 Specifies cold stamping formability, deep drawing cups, and surface cleanliness for thin-gauge corrugation plates.
Pressure Vessels, Part 2: Materials GB/T 150.2—2011 / GB 150.2 Code-mandated design stress equations, weld joint reduction parameters, and high-temperature derating coefficients.
ASME Boiler and Pressure Vessel Code ASME BPVC Section VIII Div. 1 Tables 1B (Allowable stress for non-ferrous metals vs. metal temperature limits up to 316°C for Gr. 1 and Gr. 2).
Standard Specification for Ti & Ti-Alloy Strip, Sheet, Plate ASTM B265 / ASME SB-265 International chemical composition ranges, yield strength thresholds, and bend radius criteria.
Industrial Bulk Raw Material References Alibaba / Made-in-China Industrial Metals Index (Oct 2026) Commercial base quotes for titanium sponge, cold-rolled strip coils, and hot-rolled heavy industrial plate.

Engineering Disclaimer: This guide is designed as an introductory reference for materials engineers, piping specialists, and technical purchasing agents. Allowable stresses, forming allowances, and pricing indices presented are approximations based on published industrial codes and bulk metal trends. Final vessel, piping, and heat exchanger designs must strictly implement the design stress numbers published in the legally mandated jurisdiction code (such as ASME BPVC Section VIII, EN 13445, or GB 150), alongside actual certified material test reports (CMTR) and empirical process media validation.